How to be Remote ID Ready with US FAA Regulation
We’re not too far off from March 16th, 2024 compliance date for drone operators to meet the FAA’s Remote ID rules. There are a lot of questions about the upcoming rollout of Remote ID, so we’ve prepared some answers specifically for new and existing drone owners. There are three ways drone pilots can meet the identification requirements of the Remote ID rule:
Standard Remote ID Drone
- Operate a Standard Remote ID drone (PDF) that broadcasts identification and location information of the drone and control station. A Standard Remote ID drone is one that is produced with built-in Remote ID broadcast capabilities in accordance with the Remote ID rule’s requirements.
Remote ID broadcast Module
- Operate a drone with a Remote ID broadcast module (PDF). A broadcast module is a device that broadcasts identification and location information about the drone and its take-off location in accordance with the Remote ID rule’s requirements. The broadcast module can be added to a drone to retrofit it with Remote ID capabilities. Pilots operating a drone with a Remote ID broadcast module must be able to see their drone at all times during flight.
Operate at US FAA recognized Identification areas (FRIAs)
- Operate (without Remote ID equipment) (PDF) at FAA-recognized identification areas (FRIAs) sponsored by community-based organizations (CBOs) or educational institutions. FRIAs are the only locations where UAS (drones and radio-controlled airplanes) may operate without broadcasting Remote ID message elements.
Remote ID Broadcast Module
There are two types of modules that you may purchase, one being an All-in-one (self-contained) module, which includes the battery, the module, and the antenna and is fully programmed. The other is self-contained, a self-assembly DIY which sometimes comes with a kit, and for some, you must buy individual pieces and assemble them. Unless you are very tech-savvy, I recommend the All-in-one module, which would get you up and running ASAP.
Self-Assembly DIY Modules
If you are looking for a module that is ready to use, I would recommend the All-In-One module. These modules usually contain a circuit board and do not have a built-in power source, internal antenna, or case. Manufacturers typically use these modules with the lowest cost, starting at around $40.
The following Remote ID broadcast modules have received approval from FAA:
BlueMark
- DroneBeacon MAVLink/DroneCAN Db201 Standard RemoteID Transponder € 79/Approx. USD $85
- DroneBeacon DroneCAN Db203can Standard RemoteID Transponder € 64/Approx. USD $69
- DroneBeacon Db121pcb RemoteID Broadcast Module € 99/Approx. USD $106.88
We were fortunate to get a coupon code from BlueMark/DroneScout. Please enter them during the checkout to get a 10% discount. Coupon Code: pomusa.com
Spektrum
- SkyID Remote ID Module USD$100
DIY-D
- ESP32-C3 Remote ID USD $45
A DIY kit for adding a Remote ID Module to your custom DIY aerial drone or UAS. Requires some custom assembly, such as soldering. An OpenDroneID compatible firmware is necessary. FAA approved! RID000000405
UAV Systems
- Remote ID Module USD $149.95
This remote ID is only compatible with the following drone models.
Tarot 650 / Tarpt X6 / Tarot T-18
Aurelia X4 Standard / Aurelia X6 Standard / Aurelia X6 MAX / Aurelia X6 Pro / Aurelia X8 Standard / Aurelia X8 MAX
All-In-One Modules
This all-in-one module would be the easiest to use as it would have a built-in power source, antenna, and a self-contained case.
The following Remote ID broadcast modules have received approval from FAA:
Holy Stone (Least Expensive)
Holy Stone FAA Compliant Remote Identification Broadcast Module Spare Parts for GPS Drones with Camera for Adults 4K, Remote ID broadcast Module Parts comply with US FAA Regulation.
- Holy Stone RemoteID Transponder € 84/Approx. USD $89.99
This Remote ID module is the smallest and lightest all in one Remote ID unit so far.
BlueMark
The DroneBeacon is the most cost-effective among the other modules, and you can be up and running within a couple of minutes.
- DroneBeacon Db120 RemoteID Broadcast Module With Battery € 129/ approx USD $157
- DroneBeacon Db121 RemoteID Broadcast Module € 109/ approx USD $118
We were fortunate to get a coupon code from BlueMark/DroneScout. Please enter them during the checkout to get a 10% discount.
Coupon Code: pomusa.com
Drone Tag (In-stock)
Dronetag Beacon is the bare minimum to fly your drone safe & compliant.
With the size of 2 chocolate bar squares (16 g / 0.56 oz), Beacon Swing opens the door to the digital experience for drones of all sizes.
- Dronetag Beacon (Broadcast) Approx USD $219/ €199.00
- Dronetag Mini (Network/Broadcast) Approx USD $329.00/€299.00
Drone Defence
- Drone Defence AeroPing USD $199.48
Zephyr System
I believe Zephyr is the manufacturer of the DroneBeacon product as it has the same model number and specification of DroneBeacon DB120.
- Zephyr Systems Module 100 USD $305
Aerobits
- idME PRO (Remote ID) €229.00/ Approx $323
Pierce Aerospace
- B1 Remote ID Beacon $264.95
Uavionix
- pingRID $299.00
Complete list of Drones Modules in compliance with US FAA?
Find your drone on the FAA website to get a complete list of drones and drone modules that comply with the Remote ID.
We are a participant in the Adorama Affiliate program and Amazon Services LLC Associates Program, an affiliate advertising program and we get a small commission at no cost to you, which greatly helps the site. Thank you.
